Examples... Crater Resolution...


Hyginus Area Resolution Examples


Description

This page shows images of the area around Hyginus and compares their ability to detect small craters on the Moon's surface.

Comparative Photos


This section compares the resolution of seven Earth-based photos using a Lunar Orbiter image for reference. The comparison was inspired by some discussion between Rik Hill and Bob Pilz on the Yahoo Lunar Observer's Group.

Sample
Imager
Aperture [mm]
Wavelength
Moon Diam [arc-sec]
Dawes [km]
Min Crater [km]
Min Crater/Dawes
external image Hyginus_Hill.JPG
Rik Hill
356
?
1883
0.60
1.5
2.5
external image Hyginus_CLA.JPG
CLA
1550
?
1966
0.13
1.4
11
external image Hyginus_Declercq.JPG
Bart Declercq
235
?
1962
0.87
1.3
1.5
external image Hyginus_Lammel.JPG
Stefan Lammel
254
?
1870
0.85
1.1+
1.4
external image Hyginus_Pilz.JPG
Bob Pilz
200
blue
1945
1.03
1.1-
1.0
external image Hyginus_Roach.JPG
Ed Roach
200
?
1938
1.03
0.9
0.9
external image Hyginus_Emond.JPG
François Emond
400
?
1970
0.51
0.8
1.6
external image Hyginus_Higgins.JPG
Wes Higgins
457
?
1971
0.45
0.7
1.6

    • Lunar Orbiter reference image: external image Hyginus_LO-IV-097H.JPG

Notes
  1. The Samples are identical small windows from the eight photos as calibrated with LTVT and displayed as they would appear at zero libration and with a uniform Zoom of 30. The threshold craterlet diameters were measured on the Lunar Orbiter reference image at much higher zoom. The images can be compared by opening the full-sized versions in separate windows, or web-browser tabs, and blinking between them. (click on the images to see the full-sized screenshots)
  2. The theoretical resolution limit is dependent on both the aperture and the wavelength of the observation. Wavelength data is not available for some images, and has not been analyzed for others.
  3. Moon diameter is the size of the Moon (in arc-seconds) as seen from the observers location
  4. Dawes is the crater size corresponding to the Dawes limit, computed based on the aperture and the Moon's distance, but ignoring the possible variations in imaging wavelength.
  5. Min Crater is an estimate of the true crater diameter (determined by reference to the Lunar Orbiter photo) at which some real craters are seen, others are missed, and similar-looking features turn out not to be craters.
  6. The final column is the ratio of the values in the preceding two columns. The smaller the number the closer the image approaches to the theoretical limit possible with perfect optics and seeing (there is no reason to think that the limit should be 1.0).

For those who may be interested in further exploring the images used above--


These two files can be used with the LTVT Image Grabber to automatically download the image set from the web. Note that the two largest images are the CLA and Lunar Orbiter plates, and if you already have them in your set of calibrated images, you can use any text editor to delete the references to them in the above files.

The original discussion referred to some feature size calibration charts prepared by Rik. Many of the crater sizes listed on those charts appear to be incorrect. Here is an LTVT dot file that can be used to overlay corrected sizes for any of the features measured by Rik on any image:

In general, these are not the craters that were used for determining the detection thresholds of the above photos.




This page has been edited 10 times. The last modification was made by - JimMosher JimMosher on Jul 30, 2008 1:45 pm